The bursting pressure of the disk fixed to the 10 l vessel should be equal to the maximum rupture pressure of the bursting disks to be fitted to the IBC or tank.

This entry applies to fuel cell cartridge design types shown without their packaging to pass an internal pressure test at a pressure of 100 kPa (gauge).

Some part of the steady rise in wages has been due to trade union pressures.

The 10 l vessel should be provided with a bursting disk with a set pressure in the range of the disk(s) fitted on the tank or IBC as to be used in transport.

Heavy compactor Dump truck

There's a transformer too... Just turn this thing here... and iron.

(e) dangerous rise in pressure.

Keep your blood pressure down.

Pressure receptacles may not be equipped with any pressure relief device.

The packaging shall be adequately ventilated to prevent the creation of flammable atmosphere and the build up of pressure.

Prepare descomopresión camera.

Trimage image compressor

The pressure is recorded by a pressure transducer(s) capable of recording slow and fast (at least 1000 points sec.

(a) Mini Pressurized Logistic Modules (MPLMs)

Circuit Horizontal Zener Diode

Circuit Vertical Zener Diode

3353 AIR BAG INFLATORS, COMPRESSED 2.2 280 GAS or AIR BAG MODULES, COMPRESSED GAS or SEAT BELT PRETENSIONERS, COMPRESSED GAS

Design pressure means the pressure to be used in calculations required by a recognized pressure vessel code.

Coolant pressure tester Mechanics tool chest

The transformer got struck by lightning again.

This shall be at least two thirds of the design pressure of the aerosol dispenser.

UN No. Non refrigerated liquefied gases Max. allowable working pressure (bar) Small Bare Sunshield Insulated

As far as light weapons are concerned, the situation is slightly different, owing to the higher pressures of the stronger charges fired. The strain on essential parts of the weapon, such as barrels, bolts and receivers, is much greater.

You look like your blood pressure's boiling, Charlie. What's the matter?

Any type of demonstration was quickly suppressed.

In addition, provision is made for the maintenance of workshop equipment for vehicles such as vehicle lifts, compressors, hydraulic jacks, spray painting apparatus and tyre changing machines in order to keep this equipment at the level required to comply with health and safety regulations in the Mission ( 3,000).

The second type is the piezoelectric biosensor.

Come on, boy, the coffin.

For safety, it is recommended to provide the test vessel with an extra bursting disk (bursting pressure approximately 80 of the design pressure of the 10 l test vessel) with a large opening for additional emergency venting of the test vessel in the event that the chosen orifice diameter is too small.

Holding time means the time that will elapse from the establishment of the initial filling condition until the pressure has risen due to heat influx to the lowest set pressure of the pressure limiting device(s)

I guess Ugai's blood pressure has gone up.

Violence against women was a symptom of a culture of oppression and was typical of all oppressive relationships.

The first feature of the new engine is... its greatly increased ratio of compression... represented by R minus 1 over R to the power of gamma... where R represents the ratio of compression and gamma...

But inside a standard transformer are two coils of wire.

4.1.3.6 Pressure receptacles for liquids and solids

Down converter, 24 to 12 VDC

Your blood pressure's going up just while we're talking here.

(a) Each plug or valve shall have a taper threaded connection directly to the pressure receptacle and be capable of withstanding the test pressure of the pressure receptacle without damage or leakage

By the time the helicopter arrived at Prince Henry Hospital in Sydney, my blood pressure was 40 over nothing.

(iii) Pressure sensors, pressure activated mechanisms, should, where possible, be subject to a minimum pressure force appropriate for the intended target.

4.1.3.6.3 Unless otherwise indicated, pressure receptacles having a minimum test pressure of 0.6 MPa shall be used.

Robotic Air Powered Hand with Elastic Ligaments.

Pressure vessel code to which the shell is designed

(iii) Pressure sensors shall, where possible, be subject to a minimum pressure force appropriate for the intended target.

6.6.2.8.5 When the shell is fitted for pressure discharge, the inlet line shall be provided with a suitable pressure relief device set to operate at a pressure not higher than the MAWP of the shell, and a stop valve shall be fitted as close to the shell as reasonably practicable.