Translation of "general tolerances" to Chinese language:
Dictionary English-Chinese
General - translation :
Examples (External sources, not reviewed)
| Delicate because the tolerances the team were working to were tiny just a few millimetres either way. | 说它精密 是因为工程团队需要确保偏差非常之小 每边只有几毫米 |
| Despite the massive size and weight of the bridge completing the closure between the viaduct and bridge deck is a delicate operation involving extremely precise tolerances for fit up. | 尽管该桥的规模和重量都很巨大 但是完成高架桥和桥面之间的合龙却需要精细作业 需要非常精准的装配 |
| We are studying the tolerances of the materials that you use to build the structure of your expression your speeches and your writing. And then, often people say to me, Well, OK, how do I know that this word is real? | 我们在研究不同物料的偏差 当你去架构你的表达的时候 你的演说和写作 于是人们常常对我说 那好 我怎么知道这词是真实存在的 |
| The (revised) Pesticide Regulation (EC Directive 91 414) stipulates that maximum residue levels (MRLs) of pesticides will be set by default at the limit of detection, unless producers outside the EU are able to secure import tolerances upon submission of a complete residue dossier. | (经修订的)杀虫剂规则(欧洲共同体第91 414号指令)规定欧盟以外的厂商除非能够提交完整的残留档案 否则杀虫剂最高残留限度将自动定为能查出的限度 |
| Article 14 The administrative department of public health under the State Council shall formulate or approve and promulgate the national hygiene standards, hygiene control regulations and inspection procedures for food, food additives, the containers, packagings, utensils and equipment used for food, the detergents and disinfectants used for washing food or utensils and equipment used for food, and the tolerances for contaminants and radioactive substances in food. | 第十四 条 食品 食品 添加剂 食品 容器 包装 材料 食品 用 工具 设备 用于 清洗 食品 和 食品 用 工具 设备 的 洗涤剂 消毒剂 以及 食品 中 污染 物质 放射性 物质 容许 量 的 国家 卫生 标准 卫生 管理 办法 和 检验 规程 由 国务院 卫生 行政部门 制定 或者 批准 颁发 |
| General Settings Customize general behavior | 常规设置 自定义常规行为 |
| The present general recommendation replaces general recommendation XI (1993). | 39. 本一般性建议取代第十一(1993)号一般性建议 |
| General Accounts Office, Secretariat General, Chief of Staff, 1991 | 1991 1993年 外交部副部长兼办公厅主任 |
| Separate funds for general or special purposes may be established by the General Conference or the Director General. | 大会或总干事可设立各种普通用途或特别用途基金 |
| General | 概 况 |
| General | 一般事项 |
| General | 常规imageplugins shortcuts |
| General | 综述 |
| General | 二. 一般性建议 |
| General | 概况 |
| General | 五 一般事项 |
| General | 总则 |
| General | 五. 2005年7月1日至2006年6月30日期间的拟议费用估计数 |
| General | 1General 概论 4 |
| General | 概论 |
| General | 概况 |
| Dr. Supachai Panitchpakdi, Secretary General of UNCTAD, made a general introduction. | 贸发会议秘书长卡素帕猜 巴尼巴滴博士做了一般性介绍 |
| General debate and consideration of reports submitted by the Secretary General | 一般性辩论和审议秘书长提出的报告 |
| UNITAR briefings for new delegates to the General Assembly General briefing on the work of the sixtieth session of the General Assembly | 研训所为大会新代表提供的简报 关于大会第六十届会议工作的总体简报 |
| The President The general debate of the General Assembly has now concluded. | 主席 以英语发言 大会一般性辩论现在结束 |
| Report of the Secretary General (A 60 __) (General Assembly resolution 58 269) | 秘书长的报告 A 60 __ 大会第58 269号决议 |
| One General Service (Principal level) and four General Service (Other level) posts | 一个一般事务 特等 和四个一般事务 其他职等 员额 |
| Mr. Makhdoom Ali Khan, Attorney General, Office of the Attorney General, Pakistan | Mr. Makhdoom Ali Khan, Attorney General, Office of the Attorney General, Pakistan |
| General Provisions | 第一 章 总则 |
| General principles | 第5条 |
| General Assembly | 大会 |
| General income | 一般收入 |
| General provisions | 总则 |
| General principles | 一般原则 |
| General provisions | 一般规定 |
| General provision | 一般规定 |
| General Use | 常规使用 |
| Proof General | Proof General |
| General Information | һ 㐅Ϣ |
| General objective | 5. 讲习班成果 |
| General Category | 国际货币基金 |
| General overview | 概 况 |
| General information | www.un.org arabic ga president |
| General situation | 二. 总体形势 |
| General debate | 实质性会议 |
Related searches : Closer Tolerances - Small Tolerances - Allowable Tolerances - Strict Tolerances - Part Tolerances - Wide Tolerances - Meet Tolerances - Exacting Tolerances - Geometrical Tolerances - Geometric Tolerances - Tighter Tolerances - Manufacturing Tolerances - Project Tolerances - Factory Tolerances
